加工定制: | 是 |
材質: | PUR或改性PVC |
產地: | 上海 |
單價: | 面議 |
發貨期限: | 自買家付款之日起 天內發貨 |
所在地: | 直轄市 上海 |
有效期至: | 長期有效 |
發布時間: | 2023-12-16 03:11 |
最后更新: | 2023-12-16 03:11 |
瀏覽次數: | 72 |
采購咨詢: |
請賣家聯系我
|
耐扭曲電纜的基本要求由于風力發電電纜多用在氣候條件較為惡劣的地區,
一般多用在我國的北方地區,氣候較寒冷,且晝夜溫差較大,因此風力發電電纜還必須滿足環境溫度
-45℃~+50℃,運行溫度為-40℃~+50℃的使用條件。我公司自2005年初開始致力于風力發電機
專用電纜技術的研究,參照德國DIN VDE的標準,對風力發電機專用電纜進行結構優化設計,
并選用世界上優的絕緣及護套材料,電纜的性能達到了國際水平。風力發電機專用電纜分為動力電纜、
控制電纜電纜,
電纜的優點如下:[object Object]
1、具有良好的耐低溫和耐磨性,以及耐疲勞性、耐氣候老化性能、耐微生物性能,對油品、
化學品具有極好的耐腐蝕性。普通電纜不具有耐磨性和耐腐蝕性。FDZ-YEYH風能電纜 1, with good low temperature and wear resistance, as well as fatigue resistance,
weather resistance, antimicrobial properties, oil, chemicals with excellent corrosion
resistance. Ordinary cables do not wear and corrosion resistance. 2、抗扭轉性能和彎曲性能優異:成品電纜在-40℃的低溫環境下,能經受正、反各四轉為一次、
扭轉角度為 360°,次數不少于3000次的抗扭轉性能試驗,要求電纜試驗結束后導體不發生斷裂、
護套表面不產生裂紋。普通電纜不適合在低溫情況下扭轉。 2, the anti bending properties and excellent performance of torsion: finished cable at
low temperature of -40 DEG C, can withstand the positive and negative four to one,
torsion angle is 360 degrees, the number of not less than 3000 times the anti torsion
test, after the test re of cable conductor fracture does not occur, the sheath
surface no cracks. General cable is not suitable for torsion at low temperature. 3、適用環境溫度-45℃~+110℃,運行溫度為-40℃~+110℃。普通電纜運行溫度為0℃~70℃。 3, applicable environment temperature of -45 DEG C and C 110, operation temperature
is -40 DEG C 110. The operating temperature of the ordinary cable is 0 DEG C to 70
DEG C. 4、電纜的敷設溫度不低于-30℃,普通電纜的敷設溫度為不低于0℃; 4, cable laying temperature of not less than -30 DEG C, ordinary cable laying
temperature of not less than 0 degrees c; 5、電纜彎曲半徑:固定安裝不小于電纜外徑的 4倍,移動安裝不小于電纜外徑的5倍。
普通電纜的彎曲半徑為電纜外徑的 20倍。 5, cable bending radius: fixed installation is not less than 4 times the diameter
of the cable, mobile installation is not less than the cable diameter of 5 times.
The bending radius of the ordinary cable is 20 times of the outside diameter of the cable.